Connection Event: Carrier Detect found.760.83 Iridium console active and ready... Vehicle Name: ru39 Curr Time: Wed Feb 26 17:47:49 2025 MT: 760 DR Location: 4014.530 N -7352.016 E measured 60.902 secs ago GPS TooFar: 69696969.000 N 69696969.000 E measured 1e+308 secs ago GPS Invalid : 4014.587 N -7352.182 E measured 119.53 secs ago GPS Location: 4014.530 N -7352.017 E measured 64.903 secs ago sensor:c_wpt_lat(lat)=4012.6669 711.714 secs ago sensor:c_wpt_lon(lon)=-7341.9775 711.718 secs ago sensor:m_battery(volts)=16.3843660842421 3.747 secs ago sensor:m_coulomb_amphr(amp-hrs)=0.495 3.841 secs ago sensor:m_coulomb_amphr_total(amp-hrs)=0.495 3.845 secs ago sensor:m_depth(m)=0.363311834218412 3.658 secs ago sensor:m_digifin_leakdetect_reading(nodim)=1022 0.047 secs ago sensor:m_gps_mag_var(rad)=0.225147473507269 64.949 secs ago sensor:m_iridium_attempt_num(nodim)=2 44.347 secs ago sensor:m_iridium_call_num(nodim)=2682 0.058 secs ago sensor:m_iridium_dialed_num(nodim)=3195 16.188 secs ago sensor:m_leakdetect_voltage(volts)=2.49990842490842 59.997 secs ago sensor:m_leakdetect_voltage_forward(volts)=2.49184981684982 59.961 secs ago sensor:m_leakdetect_voltage_science(volts)=2.49441391941392 59.926 secs ago sensor:m_tot_num_inflections(nodim)=60158 131.183 secs ago sensor:m_vacuum(inHg)=8.83254918192918 3.75 secs ago sensor:m_water_vx(m/s)=-0.018077754745665 60.988 secs ago sensor:m_water_vy(m/s)=0.015946918378812 60.991 secs ago sensor:u_max_altimeter(m)=200 1e+308 secs ago sensor:u_min_water_depth(m)=0 1e+308 secs ago sensor:u_use_current_correction(nodim)=1 1e+308 secs ago sensor:x_last_wpt_lat(lat)=4018.4588 1e+308 secs ago sensor:x_last_wpt_lon(lon)=-7343.3047 1e+308 secs ago ABORT HISTORY: total since reset: 1 ABORT HISTORY: last abort cause: MS_ABORT_OVERDEPTH ABORT HISTORY: last abort details: ABORT HISTORY: last abort time: 2025-02-26T16:58:11 ABORT HISTORY: last abort segment: ru39-2025-056-0-0 (0222.0000) ABORT HISTORY: last abort mission: od.mi GliderDos N -1 >760.96 No login script found for processing. GliderDos N -1 >send *.sbd *.tbd SCIENCE DATA LOGGING: science IS running CONSCI REQUESTED (using IRIDIUM as console) ASKING SCIENCE COMPUTER TO SWITCH TO COMMAND MODE via IRIDIUM :OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:0.0811 C_FIN:0.0000 SWITCHING TO SCIENCE COMMAND MODE over IRIDIUM Normal operation resumes when: SciDos> QUIT -or- Lose CD (unplug freewave/hangup iridium) -or- run longer than U_SCI_CMD_MAX_CONSCI_TIME(3600)s 808.01 3 Neutering the Freewave Console SCI: Implicitly limiting total transfer to 1800 secs, representing 180 KB total size SCI: Enumerating and selecting files About to send 1 files Prechecking is not necessary for this invocation START **B00000000000000 Starting zModem transfer of 02240000.tbd to/from ru39 size is 2946 Total Bytes sent/received: 1024 Total Bytes sent/received: 2048 Total Bytes sent/received: 2946 zModem transfer DONE for file 02240000.tbd 40.59 10 Freewave console restored REVERTING FROM SCIENCE COMMAND MODE SCIENCE COMMAND MODE TERMINATED because: Science Program QUIT (cts lowered) 841.60 GLD: Enumerating and selecting files About to send 1 files Prechecking is not necessary for this invocation selected IRIDIUM 841.62 save_and_change_sensors().... Changed u_use_ctd_depth_for_flying from 0 to 0 Changed c_science_on from 1 to 0 841.62 save_and_change_sensors().... Changed c_science_printout from 0 to 0 Waiting for motors idle :OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:0.0811 C_FIN:0.0000 START **B00000 Starting zModem transfer of 02240000.sbd to/from ru39 size is 4626 Total Bytes sent/received: 1024 Total Bytes sent/received: 2048 Total Bytes sent/received: 3072 Total Bytes sent/received: 4096 Total Bytes sent/received: 4626 zModem transfer DONE for file 02240000.sbd 880.17 restore_sensors().... Restored u_use_ctd_depth_for_flying from 0 to 0 Restored c_science_on from 0 to 1 880.18 restore_sensors().... 880.18 restore_sensors().... Restored c_science_printout from 0 to 0 SHUFFLING FILES . 880.22 GLD: Sent 1 file(s): 02240000.sbd GLD: SUCCESS Glider-Science software version match: 10.080000 Science hardware version is 3.000000 882.16 11 SCI:PROGLET house_elf begin() called 882.17 SCI: house_elf: Version 1.2 882.19 SCI:PROGLET ctd41cp begin() called 882.20 SCI: ctd41cp: Version 0.2 882.20 SCI: ctd41cp: Will be sending the following data to glider: 882.21 SCI: sci_water_cond(s/m) 882.21 SCI: sci_water_temp(degc) 882.22 SCI: sci_water_pressure(bar) 882.22 SCI: sci_ctd41cp_timestamp(timestamp) 882.23 SCI:PROGLET sbe41n_ph begin() called 882.25 SCI:PROGLET flbbcd begin() called 882.26 SCI: flbbcd: Version 0.0 882.27 SCI: flbbcd: Will be sending following data to glider: 882.28 SCI: sci_flbbcd_chlor_units(ug/l) 882.28 SCI: sci_flbbcd_bb_units(nodim) 882.29 SCI: sci_flbbcd_cdom_units(ppb) 882.29 SCI: sci_flbbcd_chlor_sig(nodim) 882.30 SCI: sci_flbbcd_bb_sig(nodim) 882.30 SCI: sci_flbbcd_cdom_sig(nodim) 882.31 SCI: sci_flbbcd_chlor_ref(nodim) 882.31 SCI: sci_flbbcd_bb_ref(nodim) 882.32 SCI: sci_flbbcd_cdom_ref(nodim) 882.32 SCI: sci_flbbcd_therm(nodim) 882.33 SCI: sci_flbbcd_timestamp(timestamp) 882.33 SCI:Bit(0) raise count is now 0. 882.34 SCI:Bit(0) raise count is now 0. 882.34 SCI:PROGLET azfp begin() called 882.47 SCI:PROGLET house_elf start() called 882.47 SCI: house_elf_run(): 0 error(s) in a row. (5 is fatal) 882.48 SCI: house_elf_run(): 0 error(s) since house_elf_begin(). (50 is fatal) GliderDos N -1 >:OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:-0.0811 C_FIN:0.0000 :OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:0.0782 C_FIN:0.0000 GliderDos N -1 >:OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:-0.0782 C_FIN:0.0000 :OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:0.0868 C_FIN:0.0000 Vehicle Name: ru39 1008 40 GliderDos: No keystroke heard for 120 seconds 480 seconds to go before running:SEQUENCE -resume_next GliderDos N -1 >:OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:-0.0926 C_FIN:0.0000 GliderDos N -1 > GliderDos N -1 > GliderDos N -1 >send -num=1 *.mbd SCIENCE DATA LOGGING: science IS running CONSCI REQUESTED (using IRIDIUM as console) ASKING SCIENCE COMPUTER TO SWITCH TO COMMAND MODE via IRIDIUM SWITCHING TO SCIENCE COMMAND MODE over IRIDIUM Normal operation resumes when: SciDos> QUIT -or- Lose CD (unplug freewave/hangup iridium) -or- run longer than U_SCI_CMD_MAX_CONSCI_TIME(3600)s 1190 86 Neutering the Freewave Console SCI: Implicitly limiting total transfer to 1800 secs, representing 180 KB total size SCI: Enumerating and selecting files SCI: No files to send SCI: Sent 0 file(s): SCI: SUCCESS 1192 Freewave console restored REVERTING FROM SCIENCE COMMAND MODE SCIENCE COMMAND MODE TERMINATED because: Science Program QUIT (cts lowered) 1193 GLD: Enumerating and selecting files About to send 1 files Prechecking is not necessary for this invocation selected IRIDIUM 1193 save_and_change_sensors().... Changed u_use_ctd_depth_for_flying from 0 to 0 Changed c_science_on from 1 to 0 1193 save_and_change_sensors().... Changed c_science_printout from 0 to 0 Waiting for motors idle START **B00000000000000 Starting zModem transfer of 02240000.mbd to/from ru39 size is 29063 Total Bytes sent/received: 1024 Total Bytes sent/received: 2048 Total Bytes sent/received: 3072 Total Bytes sent/received: 4096 Total Bytes sent/received: 5120 Total Bytes sent/received: 6144 Total Bytes sent/received: 7168 Total Bytes sent/received: 8192 Total Bytes sent/received: 9216 Total Bytes sent/received: 10240 Total Bytes sent/received: 11264 Total Bytes sent/received: 12288 Total Bytes sent/received: 13312 Total Bytes sent/received: 14336 Total Bytes sent/received: 15360 Total Bytes sent/received: 16384 Total Bytes sent/received: 17408 Total Bytes sent/received: 18432 Total Bytes sent/received: 19456 Total Bytes sent/received: 20480 Total Bytes sent/received: 21504 Total Bytes sent/received: 22528 Total Bytes sent/received: 23552 Total Bytes sent/received: 24576 Total Bytes sent/received: 25600 Total Bytes sent/received: 26624 Total Bytes sent/received: 27648 Total Bytes sent/received: 28672 Total Bytes sent/received: 29063 zModem transfer DONE for file 02240000.mbd 1376 restore_sensors().... Restored u_use_ctd_depth_for_flying from 0 to 0 Restored c_science_on from 0 to 1 1376 restore_sensors().... 1376 restore_sensors().... Restored c_science_printout from 0 to 0 SHUFFLING FILES . 1376 GLD: Sent 1 file(s): 02240000.mbd GLD: SUCCESS Glider-Science software version match: 10.080000 Science hardware version is 3.000000 1379 87 SCI:PROGLET house_elf begin() called 1379 SCI: house_elf: Version 1.2 1379 SCI:PROGLET ctd41cp begin() called 1379 SCI: ctd41cp: Version 0.2 1379 SCI: ctd41cp: Will be sending the following data to glider: 1379 SCI: sci_water_cond(s/m) 1379 SCI: sci_water_temp(degc) 1379 SCI: sci_water_pressure(bar) 1379 SCI: sci_ctd41cp_timestamp(timestamp) 1379 SCI:PROGLET sbe41n_ph begin() called 1379 SCI:PROGLET flbbcd begin() called 1379 SCI: flbbcd: Version 0.0 1379 SCI: flbbcd: Will be sending following data to glider: 1379 SCI: sci_flbbcd_chlor_units(ug/l) 1379 SCI: sci_flbbcd_bb_units(nodim) 1379 SCI: sci_flbbcd_cdom_units(ppb) 1379 SCI: sci_flbbcd_chlor_sig(nodim) 1379 SCI: sci_flbbcd_bb_sig(nodim) 1379 SCI: sci_flbbcd_cdom_sig(nodim) 1379 SCI: sci_flbbcd_chlor_ref(nodim) 1379 SCI: sci_flbbcd_bb_ref(nodim) 1379 SCI: sci_flbbcd_cdom_ref(nodim) 1379 SCI: sci_flbbcd_therm(nodim) 1379 SCI: sci_flbbcd_timestamp(timestamp) 1379 SCI:Bit(0) raise count is now 0. 1379 SCI:Bit(0) raise count is now 0. 1379 SCI:PROGLET azfp begin() called 1379 SCI:PROGLET house_elf start() called 1379 SCI: house_elf_run(): 0 error(s) in a row. (5 is fatal) 1379 SCI: house_elf_run(): 0 error(s) since house_elf_begin(). (50 is fatal) GliderDos N -1 > Vehicle Name: ru39 1380 GliderDos: No keystroke heard for 0 seconds 600 seconds to go before running:SEQUENCE -resume_next GliderDos N -1 > GliderDos N -1 >consci GLD: science IS running Choosing console...using IRIDIUM CONSCI REQUESTED (using IRIDIUM as console) GliderDos N -1 > Vehicle Name: ru39 1492 15 NOTE:GPS fix is getting stale: 796 secs old GliderDos N -1 >ASKING SCIENCE COMPUTER TO SWITCH TO COMMAND MODE via IRIDIUM SWITCHING TO SCIENCE COMMAND MODE over IRIDIUM Normal operation resumes when: SciDos> QUIT -or- Lose CD (unplug freewave/hangup iridium) -or- run longer than U_SCI_CMD_MAX_CONSCI_TIME(3600)s 1492 16 Neutering the Freewave Console SciDos> GliderDos N -1 >cd config c:/config SciDos>type proglets.dat # proglets.dat for Unit-1060 # # Date e-mail address comment # 01-14-2023 aritterbush@teledyne.com initial setting # 04-13-2023 waite@marine.rutgers.edu remove optode, add AZFP # # Science Software Ver.10.08 # # # PH CTD SN 9917 # FLBBCDSLC SN 7788 # OPTODE SN 1025 #------------------------------------------------------------------------ # CTD41CP Sea-bird CTD(SBE-41) # Continuous Profile Unit Version 2 # NOTE: This proglet is a substitute for the ctd41cp, it uses the # same output sensor names. Only 1 power bit and the UART is # different, there is also an initial line of text in the output. # ONLY one of these two CTDs may be installed at the same time. proglet = ctd41cp uart = j3 # UART4 Chan A bit = 0 # power control for sensor start_snsr = c_profile_on(sec) simulator = ctd41cp_sim # #------------------------------------------------------------------------ # Sea-bird SBE41N-pH sensor, baud rate 9600 # NOTE: This proglet must be used in conjunction with a CTD; the CTD data # is required to post-process the pH output. This sensor is a CMOS # device and must be connected to the CMOS port (J14). When using # J14, J0 cannot be used by another device. proglet = sbe41n_ph uart = j14 # CMOS port, connector J14 cannot be used in conjunction with J0 bit = 3 # power, aux power start_snsr = c_sbe41n_ph_on(sec) # #------------------------------------------------------------------------ # Wet Labs flbbcd fluorometer, scattering meter, and cdom sensor, baud rate 19200 # NOTE: This proglet requires the following sensor specific constants from # Wet Labs for deriving engineering units (put in autoexec.mi): # u_flbbcd_chlor_cwo(nodim) # clean water dark offset, nodim == counts # u_flbbcd_bb_cwo(nodim) # clean water dark offset, nodim == counts # u_flbbcd_cdom_cwo(nodim) # clean water dark offset, nodim == counts # u_flbbcd_chlor_sf(ug/l/nodim) # scale factor to get units # u_flbbcd_bb_sf(Mnodim) # scale factor to get units # u_flbbcd_cdom_sf(ppb/nodim) # scale factor to get units # u_flbbcd_is_calibrated(bool) 1 # set to 1 after entering # # calibration constants # # For simulator, set u_wetlabs_sim_num_eng_units(nodim) to 3 in autoexec.mi # proglet = flbbcd uart = j2 # connector bit = 0 # power, battery start_snsr = c_flbbcd_on(sec) simulator = wetlabs_sim # #------------------------------------------------------------------------ # Aanderaa Oxygen Optode 4330F or 4831 # NOTE: This proglet requires the following input sensor (put in autoexec.mi): # u_oxy4_slow_surface_mode(bool) 1 (default for 4330F), 0 for 4831 model # # proglet = oxy4 # uart = j1 # U4Soem Pins T-2,R-3 # bit = 2 # 8.8v # start_snsr = c_oxy4_on(sec) # #------------------------------------------------------------------------ # ASL Acoustic Zooplankton Fish Profiler (AZFP), echosounder, baud rate 9600 # proglet = azfp uart = j6 # connector bit = 5 # Pause\Go control line start_snsr = c_azfp_on(sec) # #------------------------------------------------------------------------ SciDos> GliderDos N -1 >uart j6 9600 0 bit_raise: Raising bit(0). Switching to J6 Type ctrl-c to return to glider ------------------------------------------------------------ ? ------------------------------------------------------------------------ Commands are composed of one or more characters followed by one or more parameters on one line. Commands and parameters are separated by blanks. Command or parameter letters enclosed with braces {} are optional. Parameters enclosed with square braces [] are mandatory. All addresses and values are expressed in base 16, Counts are in base 10. COMMAND PARAMETER(S) DESCRIPTION &G Deploy unit. then send ACK &F Full duplex &H Half duplex &Pico Jump to PICO DOS &Reset BIOS Reset &V Show firmware version &Wreset Reset using watchdog &S Place the unit into permanent sleep mode !S {9600,115200} :OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:-0.0608 C_FIN:0.0000 Set the SYS.BAUD variable. The SYS.CLOCK is also set !B {9600,115200,230400,460800} Temporarily set the BAUD rate to specified rate !N {9600,115200,230400,460800} Set the AZFP operating BAUD rate regardless of SYS.BAUD setting !NS Set the BAUD rate to the operating BAUD rate !NR Remove operating BAUD rate setting. Boot defaults to SYS.BAUD dn Dump system variables and parameters ds Dump system variables only dp Dump parameters only di Display files on FLASH df Display storage space on FLASH dc Display condense parameters dr Display real time parameters ee [parameter] Erase VEE parameter from VEEPROM memory (CAUTION !!!) es Show all VEE parameters ) er Read system parameters from VEEPROM and show ) ed [ERASE] Erase all parameters in the VEEPROM except SYS. (CAUTION !!!) ea [NOAUTO, AUTO] Enable or disable no auto deploy eb [ON, OFF] Enable or disable backscatter pings eo [ERASE] Erase old configuration data ex [ERASE] List and ask to erase entries (CAUTION !!!!) ec Clean up and compact VEEPROM en [SERIAL serial] View or set serial number of the instrument ev [BV version] View or set board version of the instrument ep [SET {0,1,2}] View or set backplane version of the instrument. SET sets the version 0=No backplane, 1=Up to 15V input, 2=Up to 18V input #P1 Show phase 1 #P1C [y m d hr min sec] Set the real time clock date and time #P1Dy Set phase 1 digrate all channels where y=0,1,2 0=64000 1=40000 2=20000 #P1Ky Set phase 1 average pings in the burst y=1=true y=0=false #P1FxEy Set phase 1 Acquire frequency x=freq(1,2,3,or 4) y=1=true y=0=false #P1FxDy Set phase 1 digrate where x=freq(1,2,3,or 4) y=0,1,2 0=64000 1=40000 2=20000 #P1FxP {pulse_len} Set phase 1 pulse length, x=freq(1,2,3,or 4) #P1FxRA {range_averaging} Set phase 1 range averaging x=freq(1,2,3,or 4) #P1FxRL {range_lockout} Set phase 1 range lockout x=freq(1,2,3,or 4) #P1FxRS {range_samples} Set phase 1 range samples x=freq(1,2,3,or 4) #P1RA {range_averaging} Set phase 1 range averaging all channels #P1RL {range_lockout} Set phase 1 range lockout all channels #P1RS {range_samples} Set phase 1 range samples all channels #P1Ox Set phase 1 x=R (RS232 only) x=F (FLASH & RS232) x=O (FLASH only) #P1PP {ping_period} Set phase 1 ping period #P1PI {profile_interval} Set phase 1 profile interval #P1PN {ping_per_profile} Set phase 1 pings per profile #P1S Set the AZFP to one phase, start date now, RS232 output, long duration #P1TT [minutes] Set the start date to the top of the next hour + optional minutes #P1TD [y m d hr min sec] Set the start date to optional date entered, set to now if no date is entered #P1U [ASL] Save phase parameters to VEEPROM 'ASL' command line parameter required #PI Initialize phase parameters (resets clock 1 second timer) #PG Acquire one or more and transmit one profile #PS Set the sound speed #CE Condense Pings Enable #CD Condense Pings Disable #COB RS232 output format BINARY - standard binary packet format #COA RS232 output format ASCII - ASCII output #COS RS232 output format BINARY SHORT - short binary format #CSR Storage to RS232 #CSF Storage to FLASH #CSB Storage to FLASH & RS232 #CMA Condense all profiles #CMO [N] Enable modulus mode and condense every N profile #CB [C1] [C2] [C3] [C4] Set bin averaging for each channel, min 1 max 1000 #CW Write condense parameters to VEEPROM #CR Load condense parameters from VEEPROM and display them #CZD Disable Sea-Bird modem operation #CZE Enable Sea-Bird modem operation (condensed data output only) #DIx Digital IO Mode x=1 ON, x=0 OFF, x=? report #DY [year] Create monthly directories for the specified year. Leave year out to display directories only #STx Enable/Disable first 24 status information x=1 ON, x=0 OFF, x=? report #RTx [0|1] Enable/disable the transmission of channel x=[1|2|3|4] over RS232, 0=on, 1=off #RTS Save Real time output parameters #RTE Reset real time output to all channels on #B e d i w Enable or disable secondary bounce cross talk, e=1 enable, e=0 disable direction d=0 down, d=1 up, i=instrument depth high tide, w=water depth high tide #PCx start stop Pressure Control Mode x=1 ON, x=0 OFF, x=? report, start and stop in dBar :OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:0.0724 C_FIN:0.0000 :OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:-0.0666 C_FIN:0.0000 Dir c:\DATA C:\DATA\202502 2025/02/14 07:09 PM c:\DATA\202502\20250214.LOG 61 2025/02/14 09:12 PM c:\DATA\202502\25021419.DPL 1345 2025/02/14 07:15 PM c:\DATA\202502\25021419.XML 5880 2025/02/14 07:15 PM c:\DATA\202502\25021420.DPL 1345 2025/02/14 09:12 PM c:\DATA\202502\25021420.XML 5880 2025/02/14 09:12 PM c:\DATA\202502\25021421.01A 303688 2025/02/14 09:18 PM c:\DATA\202502\25021821.DPL 1345 2025/02/18 09:39 PM c:\DATA\202502\25021821.XML 5880 2025/02/18 09:39 PM c:\DATA\202502\25022616.DPL 1345 2025/02/26 05:00 PM c:\DATA\202502\25022616.XML 5880 2025/02/26 05:00 PM c:\DATA\202502\20250226.LOG 56 2025/02/26 05:35 PM c:\DATA\202502\25022617.01A 570024 2025/02/26 05:11 PM c:\DATA\202502\25022617.DPL 1345 2025/02/26 05:35 PM c:\DATA\202502\25022617.XML 5880 2025/02/26 05:35 PM c:\DATA\202502\25022617.01B 557032 2025/02/26 05:46 PM 1 Directories 15 Files 1432 KB Used 2080 KB Free 32004128 KB Total 32006208 KB GliderDos N -1 >:OOD:digifin_mgr_ctrl:OUT OF DEADBAND: M_FIN:0.0897 C_FIN:0.0000 Parameters - 2025 02 26 18:03:30.56 Deployment Parameters Number of boards... 3 Board 0 BoardFreq. 38 Board 1 BoardFreq. 120 Board 2 BoardFreq. 200 SoundSpeed .... 1500.00 Output ............ FLASH ACQ Start Date .... 2025 2 14 18 53 34 NumPhases ......... 1 P01 Start Date .... 2025 2 14 18 53 34 P01 Duration(days). 300.0000 P01 Phase Type........ Normal P01 PingPeriod ....... 1 P01 BurstInterval..... 2 P01 PingsPerBurst..... 1 P01 AverageBurstPings. 0 P01 F1 BoardFrequency.. 38 P01 F1 acquire......... 1 P01 F1 PulseLen ....... 500 P01 F1 DigRate (hz).... 40000 P01 F1 RangeSamples.... 5300 P01 F1 LockOutIndex.... 0 P01 F1 RangeAvgSamples. 53 P01 F1 StorageFormat... linear P01 F2 BoardFrequency.. 120 P01 F2 acquire......... 1 P01 F2 PulseLen ....... 500 P0